The winter months bring more than higher gas and electric bills, often times they bring unexpected water damage by way of burst water pipes. Many of us experience just that each year and many more will join it’s rank. Pressurized indoor plumbing lines and connections exposed to extreme cold may expand and break releasing large volumes of water into attics, basements and living areas throughout homes. Within minutes water can travel from upstairs to downstairs, through walls, along foundation slabs and damage the structural integrity of residential and commercial buildings if not properly mitigated.
These blasting temperatures following a front can move into regions not accustomed to severe winter weather such as the southern United States with Texas included. And this means one thing, broken pipes. Cities such as Dallas and Ft Worth are not accustomed to the frigid cold and more susceptible to water damage from freezing plumbing failures than comparable cities located farther north.
“From 1996 to 2016, average losses for winter storms were about $1.5 billion per year for the insurance industry. The most expensive year for insured losses was 2015, at $3.5 billion,” said Peter Kim, AVP, Risk Management Services, Philadelphia Insurance Companies.
Certainly prevention is the main defense against broken pipes and water damage. By installing thicker grades of insulation in attics and between ceilings and walls a homeowner runs less of a risk but this requires added costs and not always the route taken. The fact is frozen pipes break and water spills into residential and commercial living spaces each year.
Early detection and quick water mitigation can save literally tens of thousands of dollars for homeowners and insurance companies alike. One of the first assignments for any water damage restoration company is taking moisture readings of inside areas. Water that is visible is easy to detect with the naked eye. But untamed water can pass between walls, under floors and go undetected. This can pose a real problem because moisture undetected will be the incubus for water-borne mold spores to germinate and grow after the first 48 hours. Mold poses not only a health risk to occupants but also an enormous added cost to eradicate. Thereby mapping water migration and determining the levels of moisture in walls, ceilings, and floors paves the way for proper equipment set in place to dry out all structures, restore all contents and end the threat of further damage caused by mold.
A keen eye and early detection are key to saving thousands of dollars and homeowner’s personal affect.Pioneer Plumbing & Heating Inc
Forces of nature are unpredictable at times and absolutely untamable. Just as swiftly a storm blows in it can blow out again. Dealing with the aftermath is the part we can control. Who does what and where that person does it will decide whether the outcome is successful or not. Local certified water damage restoration companies carry the skill and experience to answer tough questions and develop a drying plan with desired results successfully restoring any building compromised by broken pipes.
If you are in the process of building a new home or renovating your existing home then finding the ideal insulation is one of the decisions that you will have to make. There are several options available to you. Some products are more affordable in the short term but don’t always provide the best long-term insulation solution. Other products may be more expensive to purchase but can save you hundreds of dollars on your utility bills over time. It is useful to compare and understand the different types of insulation so you can make an informed decision that will benefit you in the long run.
Spray foam is a product that has been around for some time. It is one of the more efficient home insulators and available in a variety of types to suit different applications. It is made up of at least two compounds. Independently, the components can be stored for a relatively long period of time; however, when the compounds are mixed, they react and form foam that needs to be applied immediately. The foam is sprayed on to a surface area and after a short period of time, it sets and hardens. The result is an effective insulating layer that is highly durable.
Insulation is rated in terms of an R-value. The higher the R-value, the higher the density of the insulator and therefore the higher its effectiveness. It is considered a good insulator because of its comparatively high R-value. Open cell spray foam which has the lowest density has an R-value of 4. Most other types of spray foam have an R-value between 6 and 7.7. Compare this to fiberglass batting which is another common form of insulation that only has an R-value of 3.5. Comparatively speaking, it therefore has an average R-value that is almost double that of fiberglass batting.
Another benefit of spray foam is that the application process is much easier. It can be applied to most surfaces regardless of whether they are horizontal or vertical. In all instances the foam can simply be sprayed onto the area that needs to be insulated. There is no measuring and cutting of mats or the need to overlap insulation. It is easy to apply in a uniform manner. It is also generally more durable than other forms of insulation. It does not wear down as easily and therefore protects and insulates your home for a much longer period of time before needing to be replaced.
One of the properties of spray foam is that as it is applied to a surface area, it continues to expand. This means that the foam can get into cracks and crevasses and provide an airtight and watertight seal. It also hardens in a relatively short period of time which means that the application process can be completed in a relatively short space of time. Compared to other types of insulators, its high density is perhaps its most important characteristic. It keeps cold air out and warm air in during the winter months and helps to effectively insulate your home.
Certain types of spray foam have microbial agents as components. These microbial agents help prevent the growth of mold in your home. If you live in a region that has consistently high levels of humidity then your home can be susceptible to mold infestations. Often mold goes unseen and undetected until it is quite severe. This can affect the health of your family. Having an insulator that prevents mold growth can provide a healthier home environment. Spray foam is highly durable. It also can form a protective barrier in your home against vermin and insects. Rather than having to call exterminators, you can pre-empt the problem by insulating your home with this product.
Spray foam can be installed by a professional contractor. This is usually done in a new building or when you are doing extensive renovations. However, the good news is that there are also home kits available for those who like DIY home repairs. The easy-to-follow instructions take you through the process so you can easily insulate your home using this product.
Hot water tanks are some of the overlooked home devices in North American houses. We treat it like an afterthought until the winter season kicks in and then find oneself surprised with the dismay of cold water. We start to appreciate the value of this equipment early on when the water is too cold to bear. This is when we start to panic searching for the nearest heating repair contractor to solve the predicament.
Nearly all hot water heaters last about 10 years, at which time you can anticipate to replace it in the near future. Most hardware stores sell hot water tanks and their equivalent if you know what to do with them that is. The lifespan of these tanks could be extended either with an insulation jacket or by making certain the calcium build up in the tank are kept to a minimum. You want to follow either one or both tips to be sure that it’s going to last as long as it can be.
Although it makes logical sense that old hot water tanks need to be replaced every so often, you may wonder if it is required to get it done before it reaches the end.
Obviously, the most valuable advantage of buying a new heater will be saving cash on your utility bill. A new heater would, most likely, be more efficient than any older model. You will discover some things to consider together with your new purchase if you wish to make the most of your savings and that is how much use it is going to be subjected to.
An knowledgeable heating technician can help you work out the size and capacity of a new hot water tank according to the number of individuals in your home. In any case, extra individuals means extra hot water.
Generally, they are classified into two classifications – natural gas and electric. Gas water heaters are typically costlier to purchase and the electric types can be about the same price initially, but for the most part slightly less to buy. Most people choose the standard water heater tank, but tankless hot water heaters are likewise earning popularity, so you might want to take a look at the latter kind of hot water heater.
Regardless whether you prefer a electric or gas powered water heater, you can pick instant hot water with what is described as the on-demand water heater system. Or perhaps for people who wish to go green you may look into solar power water heaters, that greatly lessen the unsafe emissions released by older heating units. Just remember the installation difficulty you’ll face with a solar water heater, so be well prepared to pay those extra installation expenses.
No matter what type you decide on for a new water heater, you should look closely at hiring a heating contractor for the job. A gas water heater replacement demands mechanical know-how and an understanding of of local codes for ventilation and generally safe operation. If you are unfamiliar with this kind of work then do not risk your budget or your loved ones well being with a hap-hazard crack at this type of work. For top notch hot water tank service, we suggest you do your research and find a local company with a good reputation for the job.
People want to have their new homes. Many want to have their own plot and be the designer of the house. Well, one part of the design that most house owner forgets is the plumbing part. Like the designing of the house, you also require the right design to make the house’s plumbing effective. If the plumbing is not adequate, you might face severe problems in the future.
The materials used in plumbing varies a lot, depending on which kind of material you prefer. Some have an advantage over the other and the vice versa. Therefore, it becomes important that you get to know all the plumbing materials to make a perfect choice.
Iron pipes are the oldest types of pipe that are used for plumbing. They have a rich history and was commonly used in all the residential houses and building. This was mostly preferred because iron was found cheap in the market and was very easy to install too. This gave it the popularity. Moreover, the pipes have a reputation for its strength and durability. It lasted for years without leaks.
However, some issues make the iron pipe unavailable for plumbing. The pipes being made from iron welcomed rusting. The rusting of the pipe made the pipe weaker over the year that leads to failure of the durability. Most homes reported leaking due to rusting in about 25 years from installation. The rusting also changed the water taste that made the water hesitating to use.
Copper pipes have great stability and durability. They can withstand any impact and hence they can be used for any kind of plumbing. They can also be used underground without the fear of being damaged. Unlike the iron pipe, this pipes provided clean water and was free from bacterial breeding. This made the people popularly used in most countries.
One disadvantage of these pipes is they are very expensive. In addition, to that these pipes are also difficult to install. Only professional plumbers can install this, because of the required special equipment. If the water passing through the pipe is too acidic, it gives rise to corrosion in the pipe.
This pipe covers up the disadvantages of copper pipe. PVC pipe is a stable plumbing option that avoids corrosion. On the other hand, it is very easy to install and can be done by anyone. No special equipment is required in here.
The disadvantage that this pipe holds is that it is very brittle and cannot withstand force. This pipe is made of plastic and hence it cannot even withstand high temperature. This pipe can only be used in places that don’t have the high temperature to withstand.
These pipes are an extension of the PVC pipe that can withstand high temperature. It has the same holding capability of PVC pipe. Well, if you have some high-temperature piping reason then this could be used.
Now knowing all the possible options, you can choose the perfect options for plumbing your home. The cheapest one among these is PVC pipes; they are most commonly used in houses.